Is Dana 60 semi float?
Dana 60 rear axle Manufactured in both full float and semi float variations. The semi float axles have GAWR up to 5,500 lbs and the full float axles were rated up to 6,500 lbs. Full floating variants are common while Semi-floating axles exist, but are less common.
How do I know if my Dana 60 is full float?
Luckily, it’s pretty easy to tell which axle you have. The original factory axles in a Full Float Dana 60 always have 30 splines or less. If you pull an axle shaft out of your Dana and it has 33 or 35 splines, then you probably have a Dana 70.
What is semi float axle?
A semi-floating axle is very common on the rear of most 4WDs. It consists of an axle shaft on each side that is splined on the inner end where it mates to the differential and has a wheel flange where the wheel studs mount at the other end.
Is a Dana 60 good for drag racing?
The Dana 60 rearend is different from the Ford 9-inch since it’s based on a Salisbury-style rear axle and is accessed from the rear of the housing. These rearends use an ultra-strong 9-3/4-inch ring gear so they can take a beating and are perfect for drag racing.
Are Dana 60 limited slip?
The passenger car version of the Dana 60 came equipped with the Mopar “Powr-Lok” semi-float limited-slip differential option from 1966 to ’69. The Powr-Lok differential used 30-spline axles. The axle bearings, seals and retainer packages are interchangeable.
How do you tell if u have a Dana 60?
The easiest way to tell them apart is by looking at the size of the center section. Because of the way larger ring gear on the Dana 60 the center section is noticeably larger. The center section on a Dana 60 has a noticeable cutout for the larger gears. The Dana 60 axle will typically have larger brakes as well.
How can you tell the difference between a semi floating and full floating axle?
The main difference between the full- and semi-floating axle setups is the number of bearings. The semi-floating axle features only one bearing, while the full-floating assembly has bearings in both the inside and outside of the wheel hub. The other difference is about the axle removal.
Is Dana 60 stronger than Ford 9?
See all 34 photos With its huge 9-inch ring gear, a beefy Dana 60 should be stronger than a 9-inch Ford. But as these Hoosier Gear photos show, the Dana 60 (left) has only a 1.062-inch hypoid offset, compared to the Ford’s larger 2.250-inch (right).
How big is the Dana 60 rear axle?
Description: Dana 60 Rear Bolt In Axle Assembly FULL-FLOAT WITH 8X6.5 PATTERN 60.5″ WMS (OTHER WIDTH’S AVAILABLE) Base Axle Includes: Brand New Dana 60 Housing 2 – 35 Spline Chromoly… More Details » TYPICAL SHIP TIME IS 60-75 DAYS FROM DATE OF ORDER!!
What’s the difference between a Dana 60 and a Super 60?
Differences in the Dana Super 60 versus the regular Dana 60: Larger ring and pinion which increase the contact area and overall strength. Some use larger (“1550”) Universal Joints which increase strength and steering angle. Net formed spider gears for increased strength. Manufactured in both full float and semi float variations.
What kind of brakes does a Ford Dana 60 have?
Ford versions are driver’s side differential drop, reverse-cut gears, and kingpin knuckles up to 1991. The later axles have ball joints. Ford Dana 60 axles mostly feature 35 spline inner axle shafts, but some are 30 spline. Larger brakes and 35 spline outer shafts were made standard in 2005.
What kind of gearing does a Dana 60 Cummins have?
1st Generation Dodge Cummins trucks with non-OD transmissions are equipped with 3.07:1 “Dana 61” front axles with unique differential housings and carriera with extra clearance for the very large pinion gear. They can easily be “converted” to 3.54:1 gearing by replacing the carrier. Carrier break: 3.54:1 – 4.10:1 and 4.56:1 – 7.17:1