How do you make a shaft in Inventor?

By Life

How do you make a shaft in Inventor?

Design shafts

  1. On the ribbon, click Design tab Power Transmission panel Shaft .
  2. On the Design tab: In the Placement box area, specify the shaft placement within the assembly, if needed. Note: Placement is not required to design shaft using Shaft Generator.
  3. Click OK to insert a shaft to the Autodesk Inventor assembly.

What is the considered for design of the shafts?

Shafts are designed on the basis of strength or rigidity or both. Design based on rigidity is to ensure that maximum deflection (because of bending) and maximum twist (due to torsion) of the shaft is within the allowable limits.

How do you make a keyway in Inventor?

Use the Keyway dialog box to enter parameters for keyway feature in the Shaft Component Generator. Ribbon: Design tab Power Transmission panel Shaft. On the Design tab, select Cylinder in the tree control. In the Section features drop-down menu, select Add Keyway groove .

How do you add a bearing in Inventor?

Insert bearings

  1. On the ribbon, click Design tab Power Transmission panel Bearing .
  2. On the Bearing Generator, Design tab: Select the shaft cylindrical face and start plane. The shaft diameter value is automatically inserted on the Design tab. Select the type of Bearing from Content Center.
  3. Click OK.

How do you make a bearing shaft?

Shaft and housing design

  1. Shafts should be thick and short.
  2. Housings should possess sufficient rigidity.
  3. The fitting surface of the shaft and housing should be finished in order to acquire the required accuracy and roughness.
  4. The fillet radius (ra) should be smaller than chamfer dimension of the bearing.

How do you calculate shaft design?

Basic Shaft Design Formula

  1. M is maximum bending moment on the shaft.
  2. r is the radius of the shaft.
  3. I is area moment of inertia of the shaft.
  4. Input data:
  5. Solution:
  6. I = pi * r^4 *0.25.
  7. = 0.785*r^4……………….. Eqn. 1.2.
  8. r= 12.85 mm.

How do you dimension a keyway?

In the English system, it is standard practice to dimension keyways. The hub keyway is dimensioned by its width and depth on the shaft – keyway sides. Referencing Figure 1, the keyway dimension is W x T1. Unless otherwise specified, the shaft keyway is assumed to be standard.

How do you make a bearing in CAD?

To Use Bearing and Distance to Specify a Point

  1. Click Home tab Draw panel COGO drop-down COGO Input.
  2. In the COGO Input dialog box, select the Bearing/Distance routine.
  3. For the first point of an object, specify a starting point.
  4. Enter the quadrant (NE, SE, SW, NW).
  5. Enter the angle.

How to use shaft generator in Autodesk Inventor?

Use Alt + drag to move a force or support and assign it to another position marker. When designing shaft using Shaft Generator, the 3D graphical preview (with all sections, features, and 3D Grips) is available in the Autodesk Inventor window and 2D preview is available in the Design tab. 2D preview is optional.

Which is an example of a mechanical design of a shaft?

For example if thrust bearing is used. Finally, most shafts will have torsional aspect that will need to be looked at, since they are used to transfer torque from one component to another. Different grades of steel, however, does effect the yield strength and the ultimate strength of the material.

What can you do with shaft component generator?

Use the Shaft Component Generator to: Design and insert shafts with unlimited number of sections (cylinders, cones, polygons) and features (fillets, chamfers, threads, and so on.). Design shaft of a hollow shape.

Do you need a dynamic analysis for a shaft?

A shaft on the other hand will also need to have a dynamic analysis performed on it to determine fatigue stress. Article Content Links: Shaft Materials, Shaft Layout, Torque Transmission, Calculating Static Stresses, Dynamic Stresses and Fatigue, Determining Critical Stress Locations, Deflection, Critical Speed